3d_print_resources/Marlin
1
0
Fork 0
Code Issues Pull requests Releases Wiki Activity

Merge 4e2e521a82 into fbc2d2d726

Browse source
This commit is contained in:
Foxies 2020-11-13 11:02:28 +02:00 • committed by GitHub
commit 6dd2fe5df8
No known key found for this signature in database
GPG key ID: 4AEE18F83AFDEB23
1 changed files with 93 additions and 113 deletions
Download patch file Download diff file Expand all files Collapse all files

206
Marlin/src/pins/stm32f1/pins_FLSUN_HISPEED.h
View file

@ -58,7 +58,7 @@
// SPI
// Note: FLSun Hispeed (clone MKS_Robin_miniV2) board is using SPI2 interface.
//
#define SPI_DEVICE 2
#define SPI_DEVICE 2
// SPI Flash
#define HAS_SPI_FLASH 1
@ -108,49 +108,40 @@
#define E0_STEP_PIN PD6 // E0_STEP
#define E0_DIR_PIN PD3 // E0_DIR
/**
* FLSUN Hi-Speed has no hard-wired UART pins for TMC drivers.
* Several wiring options are provided below, defaulting to
* to the most compatible.
*/
//
// Drivers
//
#if HAS_TMC220x
// SoftwareSerial with one pin per driver
// Compatible with TMC2208 and TMC2209 drivers
#define X_SERIAL_TX_PIN PA10 // RXD1
#define X_SERIAL_RX_PIN PA10 // RXD1
#define Y_SERIAL_TX_PIN PA9 // TXD1
#define Y_SERIAL_RX_PIN PA9 // TXD1
#define Z_SERIAL_TX_PIN PC7 // IO1
#define Z_SERIAL_RX_PIN PC7 // IO1
#define TMC_BAUD_RATE 19200
#if ENABLED(HARDWARE_SERIAL) /* TMC2209 */
#define X_SLAVE_ADDRESS 3 // | | :
#define Y_SLAVE_ADDRESS 2 // : | :
#define Z_SLAVE_ADDRESS 1 // | : :
//#define E0_SLAVE_ADDRESS 0 // : : :
/**
* HardwareSerial with one pin for four drivers.
* The 4xTMC2209 module doesn't have a serial multiplexer and
* needs to set *_SLAVE_ADDRESS in Configuration_adv.h for X,Y,Z,E0
* and proper jumper configuration.
* Uses only one I/O pin like PA10/PA9/PC7/PA8.
* Install the jumpers in the following way, for example:
*/
//#define X_SLAVE_ADDRESS 3 // * * . JP0, JP1
//#define Y_SLAVE_ADDRESS 2 // . * . JP1
//#define Z_SLAVE_ADDRESS 1 // * . . JP0
//#define E0_SLAVE_ADDRESS 0 // . . .
#define X_SERIAL_TX_PIN PA9 // TXD1
#define X_SERIAL_RX_PIN PA9 // TXD1
#define Y_SERIAL_TX_PIN PA9 // TXD1
#define Y_SERIAL_RX_PIN PA9 // TXD1
#define Z_SERIAL_TX_PIN PA9 // TXD1
#define Z_SERIAL_RX_PIN PA9 // TXD1
#elif ENABLED(SOFTWARE_SERIAL) /* TMC220x */
/**
* TMC2208 stepper UART-configurable by PDN_UART pin
* Software serial
*/
#define X_SLAVE_ADDRESS 0
#define Y_SLAVE_ADDRESS 0
#define Z_SLAVE_ADDRESS 0
#define X_SERIAL_TX_PIN PA10 // RXD1
#define X_SERIAL_RX_PIN PA10 // RXD1
#define Y_SERIAL_TX_PIN PA9 // TXD1
#define Y_SERIAL_RX_PIN PA9 // TXD1
#define Z_SERIAL_TX_PIN PC7 // IO1
#define Z_SERIAL_RX_PIN PC7 // IO1
#endif
// Reduce baud rate to improve software serial reliability
#define TMC_BAUD_RATE 19200
#else
// Motor current PWM pins
#define MOTOR_CURRENT_PWM_XY_PIN PA6 // VREF2/3 CONTROL XY
#define MOTOR_CURRENT_PWM_Z_PIN PA7 // VREF4 CONTROL Z
@ -159,33 +150,33 @@
#define DEFAULT_PWM_MOTOR_CURRENT { 800, 800, 800 }
#endif
/**
* src: MKS Robin_Mini V2
* __ESP(M1)__ -J1-
* GND| 15 | | 08 |+3v3 (22)=>RXD1(PA10) //
* | 16 | | 07 |MOSI (21)=>TXD1(PA9) // active low, probably OK to leave floating
* IO2| 17 | | 06 |MISO (19)=>IO1(PC7) // Leave as unused (ESP3D software configures this with a pullup so OK to leave as floating)
* IO0| 18 | | 05 |CLK (18)=>IO0(PA8) // must be high (ESP3D software configures this with a pullup so OK to leave as floating)
* IO1| 19 | | 03 |EN (03)=>WIFI_EN() // Must be high for module to run
* | nc | | nc | (01)=>WIFI_CTRL(PA5)
* RX| 21 | | nc |
* TX| 22 | | 01 |RST
* ￣￣ AE￣￣
*
*/
#ifdef ESP_WIFI
#define WIFI_IO0_PIN PA8 // PC13 MKS ESP WIFI IO0 PIN
#define WIFI_IO1_PIN PC7 // MKS ESP WIFI IO1 PIN
#define WIFI_RESET_PIN PA5 // MKS ESP WIFI RESET PIN
#endif
/**
* MKS Robin_Wifi or another ESP8266 module
*
* __ESP(M1)__ -J1-
* GND| 15 | | 08 |+3v3 (22) RXD1 (PA10)
* | 16 | | 07 |MOSI (21) TXD1 (PA9) Active LOW, probably OK to leave floating
* IO2| 17 | | 06 |MISO (19) IO1 (PC7) Leave as unused (ESP3D software configures this with a pullup so OK to leave as floating)
* IO0| 18 | | 05 |CLK (18) IO0 (PA8) Must be HIGH (ESP3D software configures this with a pullup so OK to leave as floating)
* IO1| 19 | | 03 |EN (03) WIFI_EN Must be HIGH for module to run
* | nc | | nc | (01) WIFI_CTRL (PA5)
* RX| 21 | | nc |
* TX| 22 | | 01 |RST
* ￣￣ AE￣￣
*/
//Module ESP-WIFI
#define ESP_WIFI_MODULE_COM 2 // Must also set either SERIAL_PORT or SERIAL_PORT_2 to this
#define ESP_WIFI_MODULE_BAUDRATE BAUDRATE // Must use same BAUDRATE as SERIAL_PORT & SERIAL_PORT_2
#define ESP_WIFI_MODULE_RESET_PIN PA5 // WIFI CTRL/RST
#define ESP_WIFI_MODULE_ENABLE_PIN -1
#define ESP_WIFI_MODULE_TXD_PIN PA9 // MKS or ESP WIFI RX PIN
#define ESP_WIFI_MODULE_RXD_PIN PA10 // MKS or ESP WIFI TX PIN
#endif
//
// EXTRUDER
//
#if AXIS_DRIVER_TYPE(E0,TMC2208)||AXIS_DRIVER_TYPE(E0,TMC2209)
#define E0_SLAVE_ADDRESS 0
#if AXIS_DRIVER_TYPE_E0(TMC2208) || AXIS_DRIVER_TYPE_E0(TMC2209)
#define E0_SERIAL_TX_PIN PA8 // IO0
#define E0_SERIAL_RX_PIN PA8 // IO0
#define TMC_BAUD_RATE 19200
@ -199,7 +190,7 @@
#endif
//
// Temperature Sensors(THM)
// Temperature Sensors (THM)
//
#define TEMP_0_PIN PC1 // TEMP_E0
#define TEMP_BED_PIN PC0 // TEMP_BED
@ -211,7 +202,6 @@
#define HEATER_BED_PIN PA0 // HEATER_BED-WKUP
#define FAN_PIN PB1 // E_FAN
//#define CONTROLLER_FAN_PIN PD6 // BOARD FAN
//
// Misc. Functions
@ -221,6 +211,19 @@
#define POWER_LOSS_PIN PA2 // PW_DET (UPS) MKSPWC
#endif
//
//
/** Connector J2
* -------
* DIO O|1 2|O 3v3
* CSK O|3 5|O GND
* RST O|5 6|O GND
* -------
*/
//SW_DIO PA13 //
//SW_CLK PA14 //
//SW_RST NRST //(14)
//
// Power Supply Control
//
@ -240,28 +243,32 @@
//#define LED_PIN PB2 // BOOT1
#if ENABLED(NEOPIXEL_LED)
#define LED_PWM PA8
#define LED_PWM PC7 // IO1
#ifndef NEOPIXEL_PIN
#define NEOPIXEL_PIN LED_PWM // USED WIFI IO0/IO1/TX/RX PIN
#define NEOPIXEL_PIN LED_PWM // USED WIFI IO0/IO1 PIN
#endif
#endif
//Others test.
//#define SERVO0_PIN PA5 // WIFI CRTL
//#define GPIO_CLEAR PA8 // IO0
//#define GPIO_SET PA5
//
// SD Card
//
#define SDIO_SUPPORT
#define SDIO_CLOCK 4500000 // 4.5 MHz /* 18 MHz (18000000) or 4.5MHz (450000) */
//#define SDIO_CLOCK 18000000 // 18 MHz (18000000)
#define SDIO_CLOCK 4500000 // 4.5 MHz
#define SDIO_READ_RETRIES 16
#if ENABLED(SDIO_SUPPORT)
#define SCK_PIN PB13 // SPI2
#define MISO_PIN PB14 // SPI2
#define MOSI_PIN PB15 // SPI2
#define SD_DETECT_PIN PD12 // SD_CD
#define SD_DETECT_PIN -1 // SD_CD (-1 active refresh)
#define SS_PIN PC2
#else // Use the on-board card socket labeled SD_Extender
#define SCK_PIN PC12
#define MISO_PIN PC8
#define MOSI_PIN PD2
#define SS_PIN -1
#define ONBOARD_SD_CS_PIN PC11
#define SDSS PD2
#define SD_DETECT_PIN PD12 // SD_CD (if -1 no detection)
#endif
//
@ -271,6 +278,10 @@
#define BEEPER_PIN PC5
#endif
#if ENABLED(SPEAKER) && BEEPER_PIN == PC5
#error "FLSun HiSpeed default BEEPER_PIN is not a SPEAKER."
#endif
/**
* Note: MKS Robin TFT screens use various TFT controllers
* Supported screens are based on the ILI9341, ST7789V and ILI9328 (320x240)
@ -284,26 +295,7 @@
* because Marlin uses the reset as a failsafe to revive a glitchy LCD.
*/
// MKS Robin TFT v2.0 with ILI9341
// Read display identification information (0xD3 on ILI9341)
//#define XPT2046_X_CALIBRATION 12013
//#define XPT2046_Y_CALIBRATION -8711
//#define XPT2046_X_OFFSET -32
//#define XPT2046_Y_OFFSET 256
// MKS Robin TFT v1.1 with ILI9328
//#define XPT2046_X_CALIBRATION -11792
//#define XPT2046_Y_CALIBRATION 8947
//#define XPT2046_X_OFFSET 342
//#define XPT2046_Y_OFFSET -19
// MKS Robin TFT v1.1 with R61505
//#define XPT2046_X_CALIBRATION 12489
//#define XPT2046_Y_CALIBRATION 9210
//#define XPT2046_X_OFFSET -52
//#define XPT2046_Y_OFFSET -17
// QQS-Pro uses MKS Robin TFT v2.0
// QQS-Pro uses MKS Robin TFT v2.0 320x240
// Shared FSMC Configs
#if HAS_FSMC_TFT
@ -325,39 +317,27 @@
#endif
// XPT2046 Touch Screen calibration
#if EITHER(TFT_LVGL_UI_FSMC, TFT_COLOR_UI)
#if ANY(TFT_COLOR_UI, TFT_LVGL_UI, TFT_CLASSIC_UI)
#define TFT_BUFFER_SIZE 14400
#ifndef XPT2046_X_CALIBRATION
#define XPT2046_X_CALIBRATION 12218
#define XPT2046_X_CALIBRATION 12033
#endif
#ifndef XPT2046_Y_CALIBRATION
#define XPT2046_Y_CALIBRATION -8814
#define XPT2046_Y_CALIBRATION -9047
#endif
#ifndef XPT2046_X_OFFSET
#define XPT2046_X_OFFSET -35
#define XPT2046_X_OFFSET -30
#endif
#ifndef XPT2046_Y_OFFSET
#define XPT2046_Y_OFFSET 256
#define XPT2046_Y_OFFSET 254
#endif
#elif ENABLED(TFT_CLASSIC_UI)
#ifndef XPT2046_X_CALIBRATION
#define XPT2046_X_CALIBRATION 12149
#ifdef TFT_CLASSIC_UI
#define TFT_MARLINUI_COLOR 0xFFFF // White
#define TFT_BTARROWS_COLOR 0xDEE6 // Yellow
#define TFT_BTOKMENU_COLOR 0x145F // Cyan
#endif
#ifndef XPT2046_Y_CALIBRATION
#define XPT2046_Y_CALIBRATION -8746
#endif
#ifndef XPT2046_X_OFFSET
#define XPT2046_X_OFFSET -35
#endif
#ifndef XPT2046_Y_OFFSET
#define XPT2046_Y_OFFSET 256
#endif
#define TFT_MARLINUI_COLOR 0xFFFF // White
#define TFT_BTARROWS_COLOR 0xDEE6 // 11011 110111 00110 Yellow
#define TFT_BTOKMENU_COLOR 0x145F // 00010 100010 11111 Cyan
#endif
#if NEED_TOUCH_PINS