3d_print_resources/Marlin
1
0
Fork 0
Code Issues Pull requests Releases Wiki Activity

More compatible driver macros

Browse source
This commit is contained in:
Scott Lahteine 2020-10-31 16:43:17 -05:00
parent a80b3b1c00
commit f2198a1318
1 changed files with 31 additions and 29 deletions
Download patch file Download diff file Expand all files Collapse all files

60
Marlin/src/pins/stm32f1/pins_FLSUN_HISPEED.h
View file

@ -106,14 +106,15 @@
#define E0_STEP_PIN PD6 // E0_STEP
#define E0_DIR_PIN PD3 // E0_DIR
//
// Drivers
//
/**
* This board has no hard-wired UART pins for TMC drivers.
* FLSUN Hi-Speed has no hard-wired UART pins for TMC drivers.
* Several wiring options are provided below, defaulting to
* to the most compatible.
*/
//
// Drivers
//
#if HAS_TMC220x
// SoftwareSerial with one pin per driver
// Compatible with TMC2208 and TMC2209 drivers
@ -125,18 +126,18 @@
#define Z_SERIAL_RX_PIN PC7 // IO1
#define TMC_BAUD_RATE 19200
// HardwareSerial with one pins for four drivers
// Compatible with TMC2209. Provides best performance.
// Requires SLAVE_ADDRESS definitions in Configuration_adv.h
// and proper jumper configuration. Uses one I/O pins
// like PA10/PA9/PC7/PA8 only.
// position the jumpers in this way: |= close and := open.
// ex:
//#define X_SLAVE_ADDRESS 3 // | | :
//#define Y_SLAVE_ADDRESS 2 // : | :
//#define Z_SLAVE_ADDRESS 1 // | : :
// For E 0 by default whatever the mode used but remove all jumpers.
/**
* HardwareSerial with one pin for four drivers.
* Compatible with TMC2209. Provides best performance.
* Requires SLAVE_ADDRESS definitions in Configuration_adv.h and proper
* jumper configuration. Uses only one I/O pin like PA10/PA9/PC7/PA8.
* Install the jumpers in the following way, for example:
*/
//#define X_SLAVE_ADDRESS 3 // * * . JP0, JP1
//#define Y_SLAVE_ADDRESS 2 // . * . JP1
//#define Z_SLAVE_ADDRESS 1 // * . . JP0
//#define E0_SLAVE_ADDRESS 0 // . . .
#else
// Motor current PWM pins
#define MOTOR_CURRENT_PWM_XY_PIN PA6 // VREF2/3 CONTROL XY
@ -147,17 +148,18 @@
#endif
/**
* src: MKS Robin_Mini V2
* __ESP(M1)__ -J1-
* GND| 15 | | 08 |+3v3 (22)=>RXD1(PA10) //
* | 16 | | 07 |MOSI (21)=>TXD1(PA9) // active low, probably OK to leave floating
* IO2| 17 | | 06 |MISO (19)=>IO1(PC7) // Leave as unused (ESP3D software configures this with a pullup so OK to leave as floating)
* IO0| 18 | | 05 |CLK (18)=>IO0(PA8) // must be high (ESP3D software configures this with a pullup so OK to leave as floating)
* IO1| 19 | | 03 |EN (03)=>WIFI_EN() // Must be high for module to run
* | nc | | nc | (01)=>WIFI_CTRL(PA5)
* RX| 21 | | nc |
* TX| 22 | | 01 |RST
* ￣￣ AE￣￣
* MKS Robin_Mini V2
*
* __ESP(M1)__ -J1-
* GND| 15 | | 08 |+3v3 (22) RXD1 (PA10)
* | 16 | | 07 |MOSI (21) TXD1 (PA9) Active LOW, probably OK to leave floating
* IO2| 17 | | 06 |MISO (19) IO1 (PC7) Leave as unused (ESP3D software configures this with a pullup so OK to leave as floating)
* IO0| 18 | | 05 |CLK (18) IO0 (PA8) Must be HIGH (ESP3D software configures this with a pullup so OK to leave as floating)
* IO1| 19 | | 03 |EN (03) WIFI_EN Must be HIGH for module to run
* | nc | | nc | (01) WIFI_CTRL (PA5)
* RX| 21 | | nc |
* TX| 22 | | 01 |RST
* ￣￣ AE￣￣
*/
//Module ESP-WIFI
#define WIFI_IO0_PIN PA8 // MKS ESP WIFI IO0 PIN
@ -168,7 +170,7 @@
//
// EXTRUDER
//
#if AXIS_DRIVER_TYPE(E0,TMC2208)||AXIS_DRIVER_TYPE(E0,TMC2209)
#if AXIS_DRIVER_TYPE_E0(TMC2208) || AXIS_DRIVER_TYPE_E0(TMC2209)
#define E0_SERIAL_TX_PIN PA8 // IO0
#define E0_SERIAL_RX_PIN PA8 // IO0
#define TMC_BAUD_RATE 19200
@ -182,7 +184,7 @@
#endif
//
// Temperature Sensors(THM)
// Temperature Sensors (THM)
//
#define TEMP_0_PIN PC1 // TEMP_E0
#define TEMP_BED_PIN PC0 // TEMP_BED