3d_print_resources/Marlin
1
0
Fork 0
Code Issues Pull requests Releases Wiki Activity

Update pins_FLSUN_HISPEED.h

Browse source 
Remove 2209 part and  condition for Wifi Module.
This commit is contained in:
Foxies 2020-10-31 17:03:07 +01:00
parent 16569bcb7a
commit 7b596b5771
1 changed files with 42 additions and 65 deletions
Download patch file Download diff file Expand all files Collapse all files

105
Marlin/src/pins/stm32f1/pins_FLSUN_HISPEED.h
View file

@ -109,81 +109,59 @@
//
// Drivers
//
/*
* For TMC220x in UART mode and serial use,
* add #define SOFTWARE_SERIAL in you Configuration.h
* For TMC2209 in UART mode and hardware use,
* add #define HARDWARE_SERIAL in you Configuration.h
* and position the jumpers in this way.
* |= close and := open
/**
* This board has no hard-wired UART pins for TMC drivers.
* Several wiring options are provided below, defaulting to
* to the most compatible.
*/
#if HAS_TMC220x
// SoftwareSerial with one pin per driver
// Compatible with TMC2208 and TMC2209 drivers
#define X_SERIAL_TX_PIN PA10 // RXD1
#define X_SERIAL_RX_PIN PA10 // RXD1
#define Y_SERIAL_TX_PIN PA9 // TXD1
#define Y_SERIAL_RX_PIN PA9 // TXD1
#define Z_SERIAL_TX_PIN PC7 // IO1
#define Z_SERIAL_RX_PIN PC7 // IO1
#define TMC_BAUD_RATE 19200
#if ENABLED(HARDWARE_SERIAL) /* TMC2209 */
#define X_SLAVE_ADDRESS 3 // | | :
#define Y_SLAVE_ADDRESS 2 // : | :
#define Z_SLAVE_ADDRESS 1 // | : :
//#define E0_SLAVE_ADDRESS 0 // : : :
// HardwareSerial with one pins for four drivers
// Compatible with TMC2209. Provides best performance.
// Requires SLAVE_ADDRESS definitions in Configuration_adv.h
// and proper jumper configuration. Uses one I/O pins
// like PA10/PA9/PC7/PA8 only.
// position the jumpers in this way: |= close and := open.
// ex:
//#define X_SLAVE_ADDRESS 3 // | | :
//#define Y_SLAVE_ADDRESS 2 // : | :
//#define Z_SLAVE_ADDRESS 1 // | : :
// For E 0 by default whatever the mode used but remove all jumpers.
#define X_SERIAL_TX_PIN PA9 // TXD1
#define X_SERIAL_RX_PIN PA9 // TXD1
#define Y_SERIAL_TX_PIN PA9 // TXD1
#define Y_SERIAL_RX_PIN PA9 // TXD1
#define Z_SERIAL_TX_PIN PA9 // TXD1
#define Z_SERIAL_RX_PIN PA9 // TXD1
#elif ENABLED(SOFTWARE_SERIAL) /* TMC220x */
/**
* TMC2208 stepper UART-configurable by PDN_UART pin
* Software serial
*/
#define X_SLAVE_ADDRESS 0
#define Y_SLAVE_ADDRESS 0
#define Z_SLAVE_ADDRESS 0
#define X_SERIAL_TX_PIN PA10 // RXD1
#define X_SERIAL_RX_PIN PA10 // RXD1
#define Y_SERIAL_TX_PIN PA9 // TXD1
#define Y_SERIAL_RX_PIN PA9 // TXD1
#define Z_SERIAL_TX_PIN PC7 // IO1
#define Z_SERIAL_RX_PIN PC7 // IO1
#endif
// Reduce baud rate to improve software serial reliability
#define TMC_BAUD_RATE 19200
#else
// Motor current PWM pins
#define MOTOR_CURRENT_PWM_XY_PIN PA6 // VREF2/3 CONTROL XY
#define MOTOR_CURRENT_PWM_Z_PIN PA7 // VREF4 CONTROL Z
#define MOTOR_CURRENT_PWM_RANGE 1500 // (255 * (1000mA / 65535)) * 257 = 1000 is equal 1.6v Vref in turn equal 1Amp
#define MOTOR_CURRENT_PWM_RANGE 1500 // (255 * (1000mA / 65535)) * 257 = 1000 is equal 1.6v Vref in turn equal 1Amp
#ifndef DEFAULT_PWM_MOTOR_CURRENT
#define DEFAULT_PWM_MOTOR_CURRENT { 800, 800, 800 }
#endif
/**
* src: MKS Robin_Mini V2
* __ESP(M1)__ -J1-
* GND| 15 | | 08 |+3v3 (22)=>RXD1(PA10) //
* | 16 | | 07 |MOSI (21)=>TXD1(PA9) // active low, probably OK to leave floating
* IO2| 17 | | 06 |MISO (19)=>IO1(PC7) // Leave as unused (ESP3D software configures this with a pullup so OK to leave as floating)
* IO0| 18 | | 05 |CLK (18)=>IO0(PA8) // must be high (ESP3D software configures this with a pullup so OK to leave as floating)
* IO1| 19 | | 03 |EN (03)=>WIFI_EN() // Must be high for module to run
* | nc | | nc | (01)=>WIFI_CTRL(PA5)
* RX| 21 | | nc |
* TX| 22 | | 01 |RST
* ￣￣ AE￣￣
*
*/
#ifdef ESP_WIFI
#define WIFI_IO0_PIN PA8 // PC13 MKS ESP WIFI IO0 PIN
#define WIFI_IO1_PIN PC7 // MKS ESP WIFI IO1 PIN
#define WIFI_RESET_PIN PA5 // MKS ESP WIFI RESET PIN
#endif
/**
* src: MKS Robin_Mini V2
* __ESP(M1)__ -J1-
* GND| 15 | | 08 |+3v3 (22)=>RXD1(PA10) //
* | 16 | | 07 |MOSI (21)=>TXD1(PA9) // active low, probably OK to leave floating
* IO2| 17 | | 06 |MISO (19)=>IO1(PC7) // Leave as unused (ESP3D software configures this with a pullup so OK to leave as floating)
* IO0| 18 | | 05 |CLK (18)=>IO0(PA8) // must be high (ESP3D software configures this with a pullup so OK to leave as floating)
* IO1| 19 | | 03 |EN (03)=>WIFI_EN() // Must be high for module to run
* | nc | | nc | (01)=>WIFI_CTRL(PA5)
* RX| 21 | | nc |
* TX| 22 | | 01 |RST
* ￣￣ AE￣￣
*/
#define WIFI_IO0_PIN PA8 // PC13 MKS ESP WIFI IO0 PIN
#define WIFI_IO1_PIN PC7 // MKS ESP WIFI IO1 PIN
#define WIFI_RESET_PIN PA5 // MKS ESP WIFI RESET PIN
#endif
//
@ -217,7 +195,6 @@
#define HEATER_BED_PIN PA0 // HEATER_BED-WKUP
#define FAN_PIN PB1 // E_FAN
//#define CONTROLLER_FAN_PIN PD6 // BOARD FAN
//
// Misc. Functions