Multi_Config FLSUN_QQS-PRO
STOCK, TMC, UART with TFT (320x240) Standard and Marlin UI.
This commit is contained in:
Foxies
parent
f741c8df92
commit
57fbe120ff
2 changed files with 127 additions and 90 deletions
|
|
@ -21,7 +21,7 @@
|
|||
*/
|
||||
#pragma once
|
||||
|
||||
#define CONFIG_EXAMPLES_DIR "delta/FLSUN/QQ-S"
|
||||
//#define CONFIG_EXAMPLES_DIR "delta/FLSUN/QQ-S"
|
||||
|
||||
/**
|
||||
* Configuration.h
|
||||
|
|
@ -69,13 +69,18 @@
|
|||
// config/examples/SCARA and customize for your machine.
|
||||
//
|
||||
|
||||
//#define STOCK
|
||||
#define QQS
|
||||
//#define QQS_TMC
|
||||
//#define QQS_UART //Remove module ESP12
|
||||
|
||||
|
||||
//Many options for :
|
||||
//#define AUTO_BED_LEVELING_BILINEAR
|
||||
#define AUTO_BED_LEVELING_UBL
|
||||
//#define LIN_ADVANCE
|
||||
#define FILAMENT_RUNOUT_SENSOR
|
||||
#define LIN_ADVANCE
|
||||
//#define POWER_LOSS_RECOVERY
|
||||
|
||||
// @section info
|
||||
// Author info of this build printed to the host during boot and M115
|
||||
|
|
@ -123,6 +128,7 @@
|
|||
#else
|
||||
#define SERIAL_PORT 3
|
||||
#define SERIAL_PORT_2 1
|
||||
#define NUM_SERIAL 2 //MKS WIFI
|
||||
#endif
|
||||
/**
|
||||
* This setting determines the communication speed of the printer.
|
||||
|
|
@ -139,9 +145,11 @@
|
|||
//#define BLUETOOTH
|
||||
|
||||
// Choose the name from boards.h that matches your setup
|
||||
#ifndef MOTHERBOARD
|
||||
#define MOTHERBOARD BOARD_FLSUN_HISPEED
|
||||
//#define MOTHERBOARD BOARD_MKS_ROBIN_MINI
|
||||
//#ifndef MOTHERBOARD
|
||||
#if ANY(QQS, QQS_TMC, QQS_UART)
|
||||
#define MOTHERBOARD BOARD_FLSUN_HISPEED
|
||||
#else
|
||||
#define MOTHERBOARD BOARD_MKS_ROBIN_MINI
|
||||
#endif
|
||||
|
||||
// Name displayed in the LCD "Ready" message and Info menu
|
||||
|
|
@ -463,7 +471,7 @@
|
|||
#define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
|
||||
#define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
|
||||
|
||||
#define TEMP_BED_RESIDENCY_TIME 0 // (seconds) Time to wait for bed to "settle" in M190
|
||||
#define TEMP_BED_RESIDENCY_TIME 0 // (seconds) Time to wait for bed to "settle" in M190
|
||||
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
|
||||
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
|
||||
|
||||
|
|
@ -490,7 +498,7 @@
|
|||
#define HEATER_5_MAXTEMP 275
|
||||
#define HEATER_6_MAXTEMP 275
|
||||
#define HEATER_7_MAXTEMP 275
|
||||
#define BED_MAXTEMP 120
|
||||
#define BED_MAXTEMP 150
|
||||
|
||||
//===========================================================================
|
||||
//============================= PID Settings ================================
|
||||
|
|
@ -647,7 +655,7 @@
|
|||
// Delta calibration menu
|
||||
// uncomment to add three points calibration menu option.
|
||||
// See http://minow.blogspot.com/index.html#4918805519571907051
|
||||
#define DELTA_CALIBRATION_MENU
|
||||
//#define DELTA_CALIBRATION_MENU
|
||||
|
||||
// uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
|
||||
#define DELTA_AUTO_CALIBRATION
|
||||
|
|
@ -656,7 +664,7 @@
|
|||
|
||||
#if ENABLED(DELTA_AUTO_CALIBRATION)
|
||||
// set the default number of probe points : n*n (1 -> 7)
|
||||
#define DELTA_CALIBRATION_DEFAULT_POINTS 9
|
||||
#define DELTA_CALIBRATION_DEFAULT_POINTS 7//9//5 //7 //8 //6 //OPT4
|
||||
#endif
|
||||
|
||||
#if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
|
||||
|
|
@ -669,15 +677,20 @@
|
|||
|
||||
// Center-to-center distance of the holes in the diagonal push rods.
|
||||
#define DELTA_DIAGONAL_ROD 280.0 // (mm)
|
||||
|
||||
// Distance between bed and nozzle Z home position
|
||||
#define DELTA_HEIGHT 360.00 // (mm) Get this value from G33 auto calibrate
|
||||
|
||||
#define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
|
||||
|
||||
// Horizontal distance bridged by diagonal push rods when effector is centered.
|
||||
#define DELTA_RADIUS 140.8 // (mm) Get this value from G33 auto calibrate
|
||||
|
||||
// Trim adjustments for individual towers
|
||||
// tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
|
||||
// measured in degrees anticlockwise looking from above the printer
|
||||
#define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
|
||||
|
||||
// Delta radius and diagonal rod adjustments (mm)
|
||||
//#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
|
||||
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
|
||||
|
|
@ -727,12 +740,12 @@
|
|||
#endif
|
||||
|
||||
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
|
||||
#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
|
||||
#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING true // Set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
|
|
@ -827,8 +840,7 @@
|
|||
*/
|
||||
// variables to calculate steps
|
||||
#define XYZ_FULL_STEPS_PER_ROTATION 200
|
||||
#define XYZ_MICROSTEPS 16
|
||||
//#define XYZ_MICROSTEPS 32
|
||||
#define XYZ_MICROSTEPS 16 //#define XYZ_MICROSTEPS 32
|
||||
#define XYZ_BELT_PITCH 2
|
||||
#define XYZ_PULLEY_TEETH 16
|
||||
|
||||
|
|
@ -920,7 +932,7 @@
|
|||
*
|
||||
* See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
|
||||
*/
|
||||
//#define S_CURVE_ACCELERATION
|
||||
#define S_CURVE_ACCELERATION
|
||||
|
||||
//===========================================================================
|
||||
//============================= Z Probe Options =============================
|
||||
|
|
@ -1057,6 +1069,7 @@
|
|||
// 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
|
||||
// if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
|
||||
|
||||
// Kossel Mini
|
||||
#define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
|
||||
#define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_SPEED
|
||||
|
||||
|
|
@ -1066,16 +1079,21 @@
|
|||
#define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
|
||||
#define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_SPEED
|
||||
|
||||
#define Z_PROBE_ALLEN_KEY_STOW_DEPTH 20
|
||||
#define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
|
||||
#define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_SPEED
|
||||
|
||||
// Move the nozzle down further to push the probe into retracted position.
|
||||
#define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
|
||||
//#define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 23.0-(Z_PROBE_ALLEN_KEY_STOW_DEPTH) }
|
||||
#define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_SPEED)/10
|
||||
// Raise things back up slightly so we don't bump into anything
|
||||
#define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 23.0+(Z_PROBE_ALLEN_KEY_STOW_DEPTH) }
|
||||
#define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE (XY_PROBE_SPEED)/2
|
||||
//#define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
|
||||
//#define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_SPEED
|
||||
|
||||
#define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
|
||||
#define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_SPEED
|
||||
|
||||
#define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
|
||||
#define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 23.0+(Z_PROBE_ALLEN_KEY_STOW_DEPTH) }
|
||||
//#define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
|
||||
#define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_SPEED
|
||||
|
||||
#endif // Z_PROBE_ALLEN_KEY
|
||||
|
|
@ -1114,7 +1132,7 @@
|
|||
|
||||
// Most probes should stay away from the edges of the bed, but
|
||||
// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
|
||||
#define PROBING_MARGIN 10
|
||||
#define PROBING_MARGIN 10 //20
|
||||
|
||||
// X and Y axis travel speed (mm/min) between probes
|
||||
#define XY_PROBE_SPEED (133*60)
|
||||
|
|
@ -1134,7 +1152,7 @@
|
|||
* A total of 2 does fast/slow probes with a weighted average.
|
||||
* A total of 3 or more adds more slow probes, taking the average.
|
||||
*/
|
||||
//#define MULTIPLE_PROBING 2
|
||||
//#define MULTIPLE_PROBING 2 //OPT
|
||||
//#define EXTRA_PROBING 1
|
||||
|
||||
/**
|
||||
|
|
@ -1151,10 +1169,10 @@
|
|||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 15 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 15 //5 Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 //2 Z Clearance between probe points
|
||||
#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
|
||||
//#define Z_AFTER_PROBING 5 // Z position after probing is done
|
||||
//#define Z_AFTER_PROBING 5 //2 Z position after probing is done
|
||||
|
||||
#define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping
|
||||
|
||||
|
|
@ -1163,10 +1181,10 @@
|
|||
#define Z_PROBE_OFFSET_RANGE_MAX 20
|
||||
|
||||
// Enable the M48 repeatability test to test probe accuracy
|
||||
#define Z_MIN_PROBE_REPEATABILITY_TEST
|
||||
//#define Z_MIN_PROBE_REPEATABILITY_TEST
|
||||
|
||||
// Before deploy/stow pause for user confirmation
|
||||
//#define PAUSE_BEFORE_DEPLOY_STOW
|
||||
//#define PAUSE_BEFORE_DEPLOY_STOW //OPT
|
||||
#if ENABLED(PAUSE_BEFORE_DEPLOY_STOW)
|
||||
//#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe
|
||||
#endif
|
||||
|
|
@ -1182,7 +1200,7 @@
|
|||
#if ENABLED(PROBING_HEATERS_OFF)
|
||||
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
|
||||
#endif
|
||||
#define PROBING_FANS_OFF // Turn fans off when probing
|
||||
//#define PROBING_FANS_OFF // Turn fans off when probing
|
||||
//#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing
|
||||
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
|
||||
|
||||
|
|
@ -1211,9 +1229,9 @@
|
|||
|
||||
// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
|
||||
#ifdef QQS
|
||||
#define INVERT_X_DIR false
|
||||
#define INVERT_Y_DIR false
|
||||
#define INVERT_Z_DIR false
|
||||
#define INVERT_X_DIR false
|
||||
#define INVERT_Y_DIR false
|
||||
#define INVERT_Z_DIR false
|
||||
#else
|
||||
#define INVERT_X_DIR true
|
||||
#define INVERT_Y_DIR true
|
||||
|
|
@ -1222,7 +1240,7 @@
|
|||
// @section extruder
|
||||
|
||||
// For direct drive extruder v9 set to true, for geared extruder set to false.
|
||||
#define INVERT_E0_DIR true
|
||||
#define INVERT_E0_DIR true //false //extruder TITAN
|
||||
#define INVERT_E1_DIR false
|
||||
#define INVERT_E2_DIR false
|
||||
#define INVERT_E3_DIR false
|
||||
|
|
@ -1233,11 +1251,11 @@
|
|||
|
||||
// @section homing
|
||||
|
||||
#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed
|
||||
#define NO_MOTION_BEFORE_HOMING //deact Inhibit movement until all axes have been homed
|
||||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//*#define Z_HOMING_HEIGHT 15 //act (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure to have this much clearance over your Z_MAX_POS to prevent grinding.
|
||||
|
||||
//#define Z_AFTER_HOMING 10 // (mm) Height to move to after homing Z
|
||||
|
|
@ -1272,7 +1290,7 @@
|
|||
*/
|
||||
|
||||
// Min software endstops constrain movement within minimum coordinate bounds
|
||||
#define MIN_SOFTWARE_ENDSTOPS
|
||||
#define MIN_SOFTWARE_ENDSTOPS //desac
|
||||
#if ENABLED(MIN_SOFTWARE_ENDSTOPS)
|
||||
#define MIN_SOFTWARE_ENDSTOP_X
|
||||
#define MIN_SOFTWARE_ENDSTOP_Y
|
||||
|
|
@ -1313,7 +1331,7 @@
|
|||
// After a runout is detected, continue printing this length of filament
|
||||
// before executing the runout script. Useful for a sensor at the end of
|
||||
// a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
|
||||
//#define FILAMENT_RUNOUT_DISTANCE_MM 25
|
||||
#define FILAMENT_RUNOUT_DISTANCE_MM 10 //25
|
||||
|
||||
#ifdef FILAMENT_RUNOUT_DISTANCE_MM
|
||||
// Enable this option to use an encoder disc that toggles the runout pin
|
||||
|
|
@ -1364,14 +1382,14 @@
|
|||
//#define AUTO_BED_LEVELING_3POINT
|
||||
//#define AUTO_BED_LEVELING_LINEAR
|
||||
//#define AUTO_BED_LEVELING_BILINEAR
|
||||
//#define AUTO_BED_LEVELING_UBL //TMC
|
||||
//#define AUTO_BED_LEVELING_UBL //TMC define at the TOP
|
||||
//#define MESH_BED_LEVELING
|
||||
|
||||
/**
|
||||
* Normally G28 leaves leveling disabled on completion. Enable
|
||||
* this option to have G28 restore the prior leveling state.
|
||||
*/
|
||||
#define RESTORE_LEVELING_AFTER_G28
|
||||
#define RESTORE_LEVELING_AFTER_G28 //for UBL
|
||||
|
||||
/**
|
||||
* Enable detailed logging of G28, G29, M48, etc.
|
||||
|
|
@ -1411,7 +1429,7 @@
|
|||
|
||||
// Set the number of grid points per dimension.
|
||||
// Works best with 5 or more points in each dimension.
|
||||
#define GRID_MAX_POINTS_X 9
|
||||
#define GRID_MAX_POINTS_X 9 //7
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
// Probe along the Y axis, advancing X after each column
|
||||
|
|
@ -1493,7 +1511,7 @@
|
|||
* Commands to execute at the end of G29 probing.
|
||||
* Useful to retract or move the Z probe out of the way.
|
||||
*/
|
||||
//#define Z_PROBE_END_SCRIPT "G0 Z30 F12000\n G0 X0 Y0 Z30"
|
||||
//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
|
||||
|
||||
// @section homing
|
||||
|
||||
|
|
@ -1601,12 +1619,12 @@
|
|||
* M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
|
||||
* M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
|
||||
*/
|
||||
#define EEPROM_SETTINGS // Persistent storage with M500 and M501
|
||||
#define EEPROM_SETTINGS // Persistent storage with M500 and M501
|
||||
//#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
|
||||
#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
|
||||
#define EEPROM_BOOT_SILENT // Keep M503 quiet and only give errors during first load
|
||||
#if ENABLED(EEPROM_SETTINGS)
|
||||
#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors.
|
||||
#define EEPROM_AUTO_INIT // OPT Init EEPROM automatically on any errors.
|
||||
#endif
|
||||
|
||||
//
|
||||
|
|
@ -1616,7 +1634,7 @@
|
|||
// every couple of seconds when it can't accept commands.
|
||||
//
|
||||
#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
|
||||
#define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
|
||||
#define DEFAULT_KEEPALIVE_INTERVAL 5 // Number of seconds between "busy" messages. Set with M113.
|
||||
#define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating
|
||||
|
||||
//
|
||||
|
|
@ -1657,7 +1675,7 @@
|
|||
|
||||
#if ENABLED(NOZZLE_PARK_FEATURE)
|
||||
// Specify a park position as { X, Y, Z_raise }
|
||||
#define NOZZLE_PARK_POINT { (X_MIN_POS + 20), 0, 20 }
|
||||
#define NOZZLE_PARK_POINT { (X_MIN_POS + 20), 0, 40 }
|
||||
//#define NOZZLE_PARK_X_ONLY // X move only is required to park
|
||||
//#define NOZZLE_PARK_Y_ONLY // Y move only is required to park
|
||||
#define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
|
||||
|
|
@ -1870,7 +1888,7 @@
|
|||
*
|
||||
* :['JAPANESE', 'WESTERN', 'CYRILLIC']
|
||||
*/
|
||||
#define DISPLAY_CHARSET_HD44780 JAPANESE
|
||||
#define DISPLAY_CHARSET_HD44780 WESTERN
|
||||
|
||||
/**
|
||||
* Info Screen Style (0:Classic, 1:Průša)
|
||||
|
|
@ -1886,7 +1904,6 @@
|
|||
* you must uncomment the following option or it won't work.
|
||||
*/
|
||||
#define SDSUPPORT
|
||||
//#define SDIO_SUPPORT ///define in pins definitions
|
||||
|
||||
/**
|
||||
* SD CARD: SPI SPEED
|
||||
|
|
@ -1903,7 +1920,7 @@
|
|||
*
|
||||
* Use CRC checks and retries on the SD communication.
|
||||
*/
|
||||
//#define SD_CHECK_AND_RETRY
|
||||
#define SD_CHECK_AND_RETRY
|
||||
|
||||
/**
|
||||
* LCD Menu Items
|
||||
|
|
@ -2403,7 +2420,7 @@
|
|||
//
|
||||
//#define TFT_LVGL_UI_FSMC // Robin nano v1.2 uses FSMC
|
||||
//#define TFT_LVGL_UI_SPI // Robin nano v2.0 uses SPI_GRAPHICAL_TFT
|
||||
|
||||
//#define TFT_LVGL_UI
|
||||
//=============================================================================
|
||||
//============================ Other Controllers ============================
|
||||
//=============================================================================
|
||||
|
|
@ -2427,6 +2444,30 @@
|
|||
//#define XPT2046_Y_CALIBRATION -8981
|
||||
//#define XPT2046_X_OFFSET -43
|
||||
//#define XPT2046_Y_OFFSET 257
|
||||
|
||||
// Define in pins QQS-Pro (M995)
|
||||
#define XPT2046_X_CALIBRATION 12218
|
||||
#define XPT2046_Y_CALIBRATION -8814
|
||||
#define XPT2046_X_OFFSET -34
|
||||
#define XPT2046_Y_OFFSET 256
|
||||
|
||||
/* MKS Robin TFT v2.0 */
|
||||
//#define XPT2046_X_CALIBRATION 12013
|
||||
//#define XPT2046_Y_CALIBRATION -8711
|
||||
//#define XPT2046_X_OFFSET -32
|
||||
//#define XPT2046_Y_OFFSET 256
|
||||
|
||||
/* MKS Robin TFT v1.1 with ILI9328 */
|
||||
//#define XPT2046_X_CALIBRATION -11792
|
||||
//#define XPT2046_Y_CALIBRATION 8947
|
||||
//#define XPT2046_X_OFFSET 342
|
||||
//#define XPT2046_Y_OFFSET -19
|
||||
|
||||
/* MKS Robin TFT v1.1 with R61505 */
|
||||
//#define XPT2046_X_CALIBRATION 12489
|
||||
//#define XPT2046_Y_CALIBRATION 9210
|
||||
//#define XPT2046_X_OFFSET -52
|
||||
//#define XPT2046_Y_OFFSET -17
|
||||
#endif
|
||||
|
||||
//
|
||||
|
|
@ -2452,14 +2493,14 @@
|
|||
// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
|
||||
// which is not as annoying as with the hardware PWM. On the other hand, if this frequency
|
||||
// is too low, you should also increment SOFT_PWM_SCALE.
|
||||
#define FAN_SOFT_PWM
|
||||
//#define FAN_SOFT_PWM
|
||||
|
||||
// Incrementing this by 1 will double the software PWM frequency,
|
||||
// affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
|
||||
// However, control resolution will be halved for each increment;
|
||||
// at zero value, there are 128 effective control positions.
|
||||
// :[0,1,2,3,4,5,6,7]
|
||||
#define SOFT_PWM_SCALE 1
|
||||
#define SOFT_PWM_SCALE 0
|
||||
|
||||
// If SOFT_PWM_SCALE is set to a value higher than 0, dithering can
|
||||
// be used to mitigate the associated resolution loss. If enabled,
|
||||
|
|
|
|||
|
|
@ -21,8 +21,6 @@
|
|||
*/
|
||||
#pragma once
|
||||
|
||||
#define CONFIG_EXAMPLES_DIR "delta/FLSUN/QQ-S"
|
||||
|
||||
/**
|
||||
* Configuration_adv.h
|
||||
*
|
||||
|
|
@ -415,7 +413,7 @@
|
|||
// When first starting the main fan, run it at full speed for the
|
||||
// given number of milliseconds. This gets the fan spinning reliably
|
||||
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
|
||||
#define FAN_KICKSTART_TIME 100
|
||||
//#define FAN_KICKSTART_TIME 100
|
||||
|
||||
// Some coolers may require a non-zero "off" state.
|
||||
//#define FAN_OFF_PWM 1
|
||||
|
|
@ -1018,7 +1016,7 @@
|
|||
* M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2
|
||||
*/
|
||||
//#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 } // Values in milliamps
|
||||
//#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
|
||||
//*#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
|
||||
//#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis
|
||||
|
||||
/**
|
||||
|
|
@ -1056,7 +1054,8 @@
|
|||
// @section lcd
|
||||
|
||||
#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
|
||||
#define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // (mm/min) Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#define MANUAL_FEEDRATE_XYZ 50*60
|
||||
#define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // (mm/m) Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
|
||||
#if ENABLED(ULTIPANEL)
|
||||
#define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
|
||||
|
|
@ -1126,13 +1125,13 @@
|
|||
#endif // HAS_LCD_MENU
|
||||
|
||||
// Scroll a longer status message into view
|
||||
#define STATUS_MESSAGE_SCROLLING
|
||||
//#define STATUS_MESSAGE_SCROLLING
|
||||
|
||||
// On the Info Screen, display XY with one decimal place when possible
|
||||
//#define LCD_DECIMAL_SMALL_XY
|
||||
|
||||
// The timeout (in ms) to return to the status screen from sub-menus
|
||||
#define LCD_TIMEOUT_TO_STATUS 15000 //OPT
|
||||
//#define LCD_TIMEOUT_TO_STATUS 15000
|
||||
|
||||
// Add an 'M73' G-code to set the current percentage
|
||||
#define LCD_SET_PROGRESS_MANUALLY
|
||||
|
|
@ -1144,15 +1143,12 @@
|
|||
#define BOOTSCREEN_TIMEOUT 4000 // (ms) Total Duration to display the boot screen(s)
|
||||
#endif
|
||||
|
||||
#if EITHER(SDSUPPORT, LCD_SET_PROGRESS_MANUALLY) && ANY(HAS_MARLINUI_U8GLIB, HAS_MARLINUI_HD44780, IS_TFTGLCD_PANEL)
|
||||
//#define SHOW_REMAINING_TIME // Display estimated time to completion
|
||||
#if HAS_GRAPHICAL_LCD && EITHER(SDSUPPORT, LCD_SET_PROGRESS_MANUALLY)
|
||||
//#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
|
||||
#define SHOW_REMAINING_TIME // Display estimated time to completion
|
||||
#if ENABLED(SHOW_REMAINING_TIME)
|
||||
//#define USE_M73_REMAINING_TIME // Use remaining time from M73 command instead of estimation
|
||||
//#define ROTATE_PROGRESS_DISPLAY // Display (P)rogress, (E)lapsed, and (R)emaining time
|
||||
#endif
|
||||
|
||||
#if HAS_MARLINUI_U8GLIB
|
||||
//#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
|
||||
#define USE_M73_REMAINING_TIME //OPT Use remaining time from M73 command instead of estimation
|
||||
#define ROTATE_PROGRESS_DISPLAY //OPT Display (P)rogress, (E)lapsed, and (R)emaining time
|
||||
#endif
|
||||
|
||||
#if EITHER(HAS_MARLINUI_HD44780, IS_TFTGLCD_PANEL)
|
||||
|
|
@ -1188,7 +1184,7 @@
|
|||
|
||||
//#define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files
|
||||
|
||||
#define EVENT_GCODE_SD_ABORT "G28XY" // G-code to run on SD Abort Print (e.g., "G28XY" or "G27")
|
||||
#define EVENT_GCODE_SD_ABORT "G28" // G-code to run on SD Abort Print (e.g., "G28XY" or "G27")
|
||||
|
||||
#if ENABLED(PRINTER_EVENT_LEDS)
|
||||
#define PE_LEDS_COMPLETED_TIME (30*60) // (seconds) Time to keep the LED "done" color before restoring normal illumination
|
||||
|
|
@ -1202,13 +1198,13 @@
|
|||
* an option on the LCD screen to continue the print from the last-known
|
||||
* point in the file.
|
||||
*/
|
||||
//*#define POWER_LOSS_RECOVERY
|
||||
//#define POWER_LOSS_RECOVERY
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
#define PLR_ENABLED_DEFAULT true // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
|
||||
#define PLR_ENABLED_DEFAULT true // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
|
||||
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
|
||||
//#define POWER_LOSS_RECOVER_ZHOME // Z homing is needed for proper recovery. 99.9% of the time this should be disabled!
|
||||
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
|
||||
//#define POWER_LOSS_PIN PA2 or PA1 // Pin to detect power loss. Set to -1 to disable default pin on boards without module.
|
||||
//#define POWER_LOSS_PIN -1 // Pin to detect power loss. Set to -1 to disable default pin on boards without module.
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
|
|
@ -1242,7 +1238,7 @@
|
|||
* - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!)
|
||||
* - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!)
|
||||
*/
|
||||
//#define SDCARD_SORT_ALPHA
|
||||
#define SDCARD_SORT_ALPHA //OPT
|
||||
|
||||
// SD Card Sorting options
|
||||
#if ENABLED(SDCARD_SORT_ALPHA)
|
||||
|
|
@ -1258,10 +1254,10 @@
|
|||
#endif
|
||||
|
||||
// This allows hosts to request long names for files and folders with M33
|
||||
#define LONG_FILENAME_HOST_SUPPORT
|
||||
//#define LONG_FILENAME_HOST_SUPPORT
|
||||
|
||||
// Enable this option to scroll long filenames in the SD card menu
|
||||
//#define SCROLL_LONG_FILENAMES //OPT
|
||||
//#define SCROLL_LONG_FILENAMES
|
||||
|
||||
// Leave the heaters on after Stop Print (not recommended!)
|
||||
//#define SD_ABORT_NO_COOLDOWN
|
||||
|
|
@ -1424,11 +1420,11 @@
|
|||
#define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating
|
||||
#define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating
|
||||
//#define STATUS_CUTTER_ANIM // Use a second bitmap to indicate spindle / laser active
|
||||
//#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap
|
||||
//#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap
|
||||
//#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames
|
||||
#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap
|
||||
#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap
|
||||
#define STATUS_FAN_FRAMES 4 // :[0,1,2,3,4] Number of fan animation frames
|
||||
//#define STATUS_HEAT_PERCENT // Show heating in a progress bar
|
||||
//#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash)
|
||||
#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash)
|
||||
//#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~3260 (or ~940) bytes of PROGMEM.
|
||||
|
||||
// Frivolous Game Options
|
||||
|
|
@ -1489,7 +1485,7 @@
|
|||
//#define LCD_FYSETC_TFT81050 // FYSETC with 5" (800x480)
|
||||
|
||||
// Correct the resolution if not using the stock TFT panel.
|
||||
//#define TOUCH_UI_320x240 //TFT_UI
|
||||
#define TOUCH_UI_320x240 //TFT_UI
|
||||
//#define TOUCH_UI_480x272
|
||||
//#define TOUCH_UI_800x480
|
||||
|
||||
|
|
@ -1622,7 +1618,7 @@
|
|||
#define BABYSTEP_MULTIPLICATOR_Z 1 // (steps or mm) Steps or millimeter distance for each Z babystep
|
||||
#define BABYSTEP_MULTIPLICATOR_XY 1 // (steps or mm) Steps or millimeter distance for each XY babystep
|
||||
|
||||
#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
|
||||
#define DOUBLECLICK_FOR_Z_BABYSTEPPING //OPT Double-click on the Status Screen for Z Babystepping.
|
||||
#if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
|
||||
#define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
|
||||
// Note: Extra time may be added to mitigate controller latency.
|
||||
|
|
@ -1634,7 +1630,7 @@
|
|||
|
||||
//#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28
|
||||
|
||||
#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping
|
||||
//#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping
|
||||
#if ENABLED(BABYSTEP_ZPROBE_OFFSET)
|
||||
//#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
|
||||
//#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
|
||||
|
|
@ -1658,12 +1654,12 @@
|
|||
*
|
||||
* See https://marlinfw.org/docs/features/lin_advance.html for full instructions.
|
||||
*/
|
||||
//#define LIN_ADVANCE
|
||||
//#define LIN_ADVANCE //define at the TOP
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
//#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants
|
||||
#define LIN_ADVANCE_K 0 //0.22 // Unit: mm compression per 1mm/s extruder speed
|
||||
//#define LA_DEBUG // If enabled, this will generate debug information output over USB.
|
||||
#define EXPERIMENTAL_SCURVE // Enable this option to permit S-Curve Acceleration
|
||||
#define EXPERIMENTAL_SCURVE //OPT Enable this option to permit S-Curve Acceleration
|
||||
#endif
|
||||
|
||||
// @section leveling
|
||||
|
|
@ -1968,7 +1964,7 @@
|
|||
#define SERIAL_OVERRUN_PROTECTION
|
||||
|
||||
// For serial echo, the number of digits after the decimal point
|
||||
//#define SERIAL_FLOAT_PRECISION 4
|
||||
#define SERIAL_FLOAT_PRECISION 5 //OPT /4
|
||||
|
||||
// @section extras
|
||||
|
||||
|
|
@ -2114,9 +2110,9 @@
|
|||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 700 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 100 // (mm) Length to extrude after loading.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
|
@ -2134,7 +2130,7 @@
|
|||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
#define HOME_BEFORE_FILAMENT_CHANGE // If needed, home before parking for filament change
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // If needed, home before parking for filament change
|
||||
|
||||
#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
|
|
@ -3269,9 +3265,9 @@
|
|||
* Host Prompt Support enables Marlin to use the host for user prompts so
|
||||
* filament runout and other processes can be managed from the host side.
|
||||
*/
|
||||
#if EITHER(QQS, QQS_TMC) //with module ESP12
|
||||
#define HOST_ACTION_COMMANDS
|
||||
#endif
|
||||
//#if EITHER(QQS, QQS_TMC) //with module ESP12
|
||||
//#define HOST_ACTION_COMMANDS
|
||||
//#endif
|
||||
#if ENABLED(HOST_ACTION_COMMANDS)
|
||||
//#define HOST_PROMPT_SUPPORT
|
||||
//#define HOST_START_MENU_ITEM // Add a menu item that tells the host to start
|
||||
|
|
|
|||
Loading…
Add table
Add a link
Reference in a new issue